• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Door Repair - Simple Fixes You Can Do in a Few Easy Steps

While it's easy to think a door [empty] is beyond repair but there are a number of simple fixes that can make a huge difference. Let's begin with the shimming.

To shim an opening, open the door and window glass replacement repair (http://tujuan.grogol.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) and press it into the frame. Use a block or jack plane to remove small pieces of wood from the binding points.

The Frame

The door frame is a crucial element of your home. It is important for your home's security, since it protects against water damage. But it's also prone to damage. Whether from bad weather or burglaries, or just regular use, door frames can become damaged. If they do, it can result in large gaps, weak latching and an unsightly appearance. Repairing your door frame is a matter of only a few easy steps.

The first step is to take the trim, or molding, from the door opening. You can use a hammer, the chisel or a power saw to remove the trim. After the trim has been removed, make a note of the dimensions so that you can put it back in place once the window repair near me is completed.

Next, you'll need to check the door frame for any areas that are damaged or damaged. If you discover any rotten wood, you'll have to replace it. These are usually available at your local hardware store and should be constructed of a material that matches the rest your door frame. Avoid pressure-treated wood since it can twist and warp with time.

After replacing any damaged parts of the frame, you'll have to secure it. This can be accomplished by using the shank. A Shim is a piece of wood that is placed between the frame and the wall. The shim will provide extra support to the frame and prevent it from moving.

After you've replaced the shims, it is a good idea to seal the frame and the sill of your door. This will stop water damage and protect your door frame from insects.

Finally, you will need to install the trim again on the door frame. If you're lucky, the old trim might be in good shape and you can just put it back on. If not, you'll need to purchase new trim and follow the same procedure.

The Threshold

A threshold for a door is the piece of wood that covers and seals the space between the door and a floor surface. It also helps prevent snow and water from building up within the entrance. A properly installed threshold is not only an essential part of your door, but also a beautiful accent to enhance the curb appeal of your house. If your threshold is scratched or damaged, it's time to replace it. Installing a threshold is more complex than simply sliding it under the casing, and then nailing it in place. It has to be supported by shims placed between the frame’s two jambs.

Cut the old threshold away from the sides using a circular blade (use carbide blades if you are able). If you are able remove the sub sill, which is the portion of the frame that is under the threshold. If it's decaying, replace it at the same time you replace the threshold.

Before cutting the threshold to the proper size, use a square for marking layout lines on it, and note right angles to make notches that will fit around the jambs. You can also buy pre-cut thresholds that match the dimensions of your doorway in a home center.

Install the shims, making sure to space them evenly. If you need to, you can vary the thickness of the shims. However they shouldn't be larger than 1 1/2 inches. It may take some trial and error to reach a threshold that is just right, but still able to move freely.

Check the suitability of your new threshold by closing the door and testing the ease with which it closes and opens. There shouldn't be any light beneath the door, and the sweep at the bottom of the doors should be lightly rubbing the top of the threshold.

If the threshold is snug but needs some extra support, apply a construction adhesive to the shims prior to pressing them down under the threshold. Repeat the process until you get a snug fit and it holds up to weight.

The Hinges

Many hinges on doors get rusty or worsen over time, making it harder to close the door. When this happens, it's important to repair the hinge in order that the door can be closed and secured properly. When replacing the hinge, ensure that you select one that's comparable in size and shape. You should also make sure the hinge is placed correctly in the mortise and door jamb.

Check the hinge to see if it is loose. If the hinge isn't tight, it will likely be rubbing against the strike plate and bind on the frame. Look for scratched paint or indents within the frame that indicate where the hinge is rubbing. If the hinge is not tight enough, tighten it with the help of a screwdriver. If the hinge is too loose, you could need to replace it. You can try putting a shim in between the door frame and the hinge.

If the problem is that the knuckles on the hinge (the cylinders that the hinge pin goes) are bent and need to be straightened, you'll have to straighten them up to point towards the jamb of the latch. This can be done by gently bent the knuckles using a pair of tongue-and-groove pliers, or an adjustable wrench, misted up double glazing Replacement (tiresright.com) but it's best to work on just one knuckle at a time so that you don't bend the hinge leaf out of its mortise.

It's also possible the screws that hold your door hinges in place have become stripped. If this is the situation, you can replace the screws to give them a better grip on the hinges.

If the hinge isn't damaged and the screw holes are not damaged, use a syringe and inject carpenter's glue into the joint and mortise of the hinge. Then screw the hinge into the frame, and secure it with the screwdriver or drill. If you're putting in new hinges it's best to mark the locations of the pilot holes on the door as well as the door frame to make certain to place the screws in exactly the same place as the previous ones.

The Hardware

Most people don't pay much attention to door knobs, locks or levers until they stop functioning properly. The majority of these parts are easily repairable. Replacing a door handle or knob is generally a matter of picking out the piece that is the most appropriate to the style and finish of your house and then installing it. For doors that are outside, it's often recommended to add weather stripping too.

You might be able to resolve the issue of a door that is difficult to open by lubricating your lock assembly. Many hinges, handles and locks may become stuck when their wear surfaces get dry or dirty. It is not expensive to keep these components lubricated and clean.

Some of the most common problems with door hardware include loose or broken handle screws, a lock that doesn't turn when you insert the key, or hinges that squeak or become bind. In most situations you can tighten these screws or replace the screw entirely. In certain situations, however, it is better to take the lock and handle from the door, and then sand the spindle and the bore holes for the lock cylinder as well as the escutcheon holes to make sure they are free of dirt prior to installing the new hardware.

If you have doors that are difficult to close, it might be necessary to grease its locking mechanism using penetrating oils. For hinges that are squeaky you can take out and clean the hinge pins, then replace them with longer screws that will be more likely to secure.

If you're planning to replace a lock, handle or hinge, be sure to select a model that's compatible with the existing hole size on your door and jamb. You can usually find this information in the packaging or on the website of the manufacturer. For example, a deadbolt requires an opening of 1 1/2-inch or 2 1/8-inch diameter, and doorknobs and levers require holes that have a different spread (the distance between the center of the knob and the hole for locking). Check the backset to determine whether the replacement is compatible with.